Inside the Soda Can - The Can Ripper Did you know that soda cans have a thin, plastic liner inside? email to friend
print this page

The Can Ripper Demonstration

The science teacher shows her amazing strength by ripping an "ordinary" soda can in half. As you might imagine, the soda can is far from ordinary. The inside of an aluminum can is scratched with a file to remove the thin plastic coating. A solution of copper chloride is added and the aluminum is oxidized as the copper is reduced. After a few minutes, one can rip the can in half.

Procedure - Must be performed by an adult!

• Mix 10 g copper chloride crystals with 500 mL water until dissolved.
• Use file to scratch a line entirely around the inside of a can.
• Pour copper chloride solution into a can past the scratched line.
• Let the can sit for 15 to 20 minutes in the 400 mL beaker.
• When scratched line becomes more pronounced, pour solution into the beaker and rip the can in half.

There's a trick to knowing just when to pour out the solution of copper chloride before it eats all the way through the aluminum and the can falls apart on its own. It's also a good idea to wear gloves when "ripping" the can apart.

Did you know... The main acid in most soda pop is carbonic acid. Some sodas still contain phosphoric acid (which eats away at your teeth!). Both acids are much weaker than hydrochloric acid, which is the natural stomach acid. A can of pop does not make stomach contents much more acidic. In fact flat soda pop is sometimes recommended as a remedy for nausea. It actually soothes stomach irritations.

Inside the Can - Exposing the Soda Can Liner

Exposing the soda can liner that you saw in the video or in the pictures to the right requires the use of a strong base called sodium hydroxide. This procedure must be performed in a lab with a fume hood.

Procedure - Must be performed by an adult!

• Put on your safety glasses, safety gloves and splash resistent apron. This is serious!!!
• Rinse out a recycled soda can with water.
• Use a coarse sand paper to scratch the paint off the middle part of the soda can. You want the strong base to be able to react with the exposed aluminum metal.
• Fill the soda can with tap water.
• Fashion a hook (using strong paper clips, for example) to attach to the tab on the top of the can.
• Place the can in a 600 mL beaker and pour just enough 6M sodium hydroxide into the beaker to cover three quarters of the can. THIS MUST BE PERFORMED IN A FUME HOOD!
• Over the span of five to ten minutes, the strong base will dissolve the thinest parts of the aluminum can to reveal the plastic lining.
• Making sure your gloves, glasses and apron are still on, carefully remove the soda can from the solution of sodium hydroxide and immediately rinse the outside of the can in the sink. Carefully pour the water out of the can (hopefully without tearing the liner).

It's important to note that many attempts were made to create the soda can that was used on the video. If you get it the first time you try it, you're amazing!

How does it work?

As you've discovered, aluminum cans have a polymer coating on the inside of the can. When the file is used to scrape away the polymer coating, the aluminum metal is exposed. The aluminum reacts with the copper chloride solution and an electron exchange takes place. Aluminum gives electrons to the copper ions. This causes the copper ions to turn into copper metal.

At the same time aluminum metal turns into aluminum ions. Al metal + Cu+2 ions ---> Al +3 ions + Cu metal The solution ions become a metal (Cu) which are the orange red particles you see at the bottom of the solution. The new aluminum ions have different properties than the aluminum metal. This is why you can easily rip the can in half. The aluminum ions are not in a solid form, but dissolve into the liquid.

Additional Info

The History of the Liner - Technicians at the American Can Company, even before prohibition, began toying with the idea of putting beer in a can. As early as 1929, Anheuser-Busch and Pabst experimented with the canning process. Schlitzeven proposed a can design that looked like a small barrel.

The major problem the early researchers were confronted with, however, was not strength, but the can's liner. Several years and most of the early research funds were spent to solve this perplexing problem. Beer has a strong affinity for metal, causing precipitated salts and a foul taste. The brewers called the condition "metal turbidity".

The American Can Company produced the flat or punch top can in 1934. The lining was made from a Union Carbide product called "Vinylite", a plastic product which was trademarked "keglined" on September 25, 1934.

Reference - A special thanks to Flinn Scientific for the explanation of the soda can ripper.